Showing posts with label Electronics. Show all posts
Showing posts with label Electronics. Show all posts

Saturday, June 25, 2011

DIY - Very LOW COST emergency charger

Ever thought about making an adventure travel into the wilderness, but not wanting to get rid of your phone, MP3 or GPS? What if the trip takes several days and you've no place to charge your equipment? You could buy a solar charger, which are not that cheap and take really long to charge. You could have a spare batery for your phone, but then again it's not cheap and in some cases it's annoying to make the replacement. Or you could use spare and very low cost parts and build one yourself, giving you the joy of using something self made.

With simple AA chargeable batteries you can give some precious juice to your portable equipment to keep it running. With the benefit that you can charge the batteries again as soon as you get to civilization and you can use as many battery sets as your back can handle.

The AA chargeable batteries provide a maximum voltage around 1.25V instead of the alkaline non chargeable ones (1.5V). Connecting them in serial mode will give your equipment approximately 5V, which is the tension needed for the USB charged devices.

  1. micro USB connector ( 1€ )
  2. 4 AA battery socket holder ( 0.3 € )
  3. 9V battery connector snap ( 0.17 € )
  4. soldering connections and silicon glue
Since I couldn't find a place selling a micro USB connector, just bought a cable in a chinese shop and cut the part i needed. After that, the only tricky part is soldering the cables: make sure you connect red with red and black with black. The silicon glue will make the connection isolated and robust since the wires are very thin.

If you want you can even connect several distinct adapters instead of only micro USB.

Another important thing to keep in mind are the batteries capacity! They should be higher than your equipments. For example my Galaxy S has a 1500mAh battery, meaning I've to use at least the same capacity or it won't make a full charge. 

Saturday, February 26, 2011

Resistor value calculator in HTML5

A resistor is a two-terminal electronic component which implements electrical resistance as a circuit element. When a voltage V is applied across the terminals of a resistor, a current I will flow through the resistor in direct proportion to that voltage. The reciprocal of the constant of proportionality is known as the resistance R, since, with a given voltage V, a larger value of R further "resists" the flow of current I as given by Ohm's law.


Most axial resistors use a pattern of colored stripes to indicate resistance. Surface-mount resistors are marked numerically, if they are big enough to permit marking; more-recent small sizes are impractical to mark. Cases are usually tan, brown, blue, or green, though other colors are occasionally found such as dark red or dark gray.
Early 20th century resistors, essentially uninsulated, were dipped in paint to cover their entire body for color coding. A second color of paint was applied to one end of the element, and a color dot (or band) in the middle provided the third digit. The rule was "body, tip, dot", providing two significant digits for value and the decimal multiplier, in that sequence. Default tolerance was ±20%. Closer-tolerance resistors had silver (±10%) or gold-colored (±5%) paint on the other end.


Four-band identification is the most commonly used color-coding scheme on resistors. It consists of four colored bands that are painted around the body of the resistor. The first two bands encode the first two significant digits of the resistance value, the third is a power-of-ten multiplier or number-of-zeroes, and the fourth is the tolerance accuracy, or acceptable error, of the value. The first three bands are equally spaced along the resistor; the spacing to the fourth band is wider. Sometimes a fifth band identifies the thermal coefficient, but this must be distinguished from the true 5-color system, with 3 significant digits.
For example, green-blue-yellow-red is 56×104 Ω = 560 kΩ ± 2%. An easier description can be as followed: the first band, green, has a value of 5 and the second band, blue, has a value of 6, and is counted as 56. The third band, yellow, has a value of 104, which adds four 0's to the end, creating 560,000 Ω at ±2% tolerance accuracy. 560,000 Ω changes to 560 kΩ ±2% (as a kilo- is 103).

To try out EaselJS (a javascript library for working with the html5 canvas element) and inspired by Resistor Colour Wheel I wrote a small experiment, that can help finding the value of resistors: HTML5 Resistor calculator.




ALERT! This experiment won't work at all in Internet Explorer. You need Chrome, Firefox, Safari or any other browser supporting HTML5.